Skyddsglasögon
Skyddsglasögon
På begäran kommer lite info avseende skyddsglasögon 06? (07?).
Finns i tre glas, klart, gult och mörkt. Förpackas i en praktisk ask med tillhörande skalmar, nackband och en liten påse.
Här finns mer info.
Finns i tre glas, klart, gult och mörkt. Förpackas i en praktisk ask med tillhörande skalmar, nackband och en liten påse.
Här finns mer info.
Re: Skyddsglasögon
1) TackMD650 skrev:Förpackas i en praktisk ask med tillhörande skalmar
2) Jag läste skalman
3) Peltor, jag har hörselkåpor (med mikrofoner och batterier) från början av nittiotalet som fortfarande nästan fungerar
4) Kan någon översätta: CSA Z94.3-2007 and the High Impact Requirements of ANSI Z87.1-2003. Meets Military Vo Regimen for High Velocity Impact^.
^Complies to MIL-PRF-31013 Using Test Method MIL STD 662F (V50) Ballistic Test for Armor)-T37 Shaped (.15Cal) Projectile @ 650 ft/sec = 440 mph
MVH
Hans
- B Hellqvist
- Redaktör emeritus
- Inlägg: 5627
- Blev medlem: 24 mars 2002, 16:05
- Ort: Skövde
- Kontakt:
Re: Skyddsglasögon
Hans, det rör sig om olika säkerhetsstandarder för skyddsglasögon, där man strävar efter att linserna ska klara standariserade tester med en kula eller spets av viss tyngd och som färdas i en viss hastighet. Jag kan inte säga exakt vad de klarar, men de borde klara mindre splitter och blyhagel.
Re: Skyddsglasögon
Tack men ungefär så mycket begrep jag själv - finns det någon lite mer precis sammanfattning?
Jag har en polare här nere som är enögd efter att ha gjort bomber i tonåren - som skjuter hejvilt varje söndag utan glasögon - och jag funderar på att ge honom ett par (monokel ) - därav mina frågor.
MVH
Hans
Jag har en polare här nere som är enögd efter att ha gjort bomber i tonåren - som skjuter hejvilt varje söndag utan glasögon - och jag funderar på att ge honom ett par (monokel ) - därav mina frågor.
MVH
Hans
Re: Skyddsglasögon
Har för mig att det står 166 (0) ft på skalmen eller glaset och det kan tyda på att den skall klara en viss "mängd" projektil upp till 166 fot/s.
Utan att vetenskapligt bevisa det så enl. uppgift skall glaset tåla hagel på 2- 5m??.
Utan att vetenskapligt bevisa det så enl. uppgift skall glaset tåla hagel på 2- 5m??.
Re: Skyddsglasögon
http://blogg.webfotografen.com/
http://blogg.ud.se/blog/2010/11/01/sver ... -handelse/
Och jag som trodde att det var ballfaktorn som låg bakom alla solglasögonprydda soldater
MVH
Hans
Re: Skyddsglasögon
Det är många proffstyckare som har tyckt det.Hans skrev:Och jag som trodde att det var ballfaktorn som låg bakom alla solglasögonprydda soldater
MVH
Hans
Re: Skyddsglasögon
Utöver det ballistiska skyddet så ska vi inte glömma att det ofta är stark sol i Afghanistan. Då behöver man solglasögon även om man är soldat...
Re: Skyddsglasögon
Dom liknar ju inte ens dom man får ut i HV
Re: Skyddsglasögon
MIL-PRF-31013 Summary
There are many specific categories outlined in the PRF-31013 standard. The most common clause referenced in the standard is that of 3.5.1.1 for ballistics/impact testing. In general conversation, references to an eyewear's "ballistics" rating commonly refer to its ability to withstand impact at high velocity. Thus, we will focus on this area. To see our selection of Ballistic eyewear, click here.
3.5.1.1
Ballistic Resistance
The ballistic resistance of the spectacles shall be such that they will pass a Vo test using a 0.15 caliber, 5.8 grain, T37 shaped projectile at a velocity of 640 to 660 feet per second when tested as specified in 4.4.1.1.
4.4.1.1
Ballistic Resistance
The test shall be a Vo test conducted as specified in MIL-STD-662 using a 0.15 caliber, 5.8 grain, T37 shaped projectile with the following exceptions: electronic velocity detection devices (light beam or acoustic type) may be used to determine the velocity of the projectile, such devices placed no less than 8 inches and no more than 24 inches from the target; compressed gas propulsion of the projectile may be used. The eyewear shall be mounted on an Alderson 50th percentile male headform in the as-worn position. The 0.002 inch thick aluminum foil witness sheet shall be mounted within 2 inches of the eyewear behind the area of impact. The sample shall be hit once at normal incidence within a l-inch diameter at a point centered vertically and at a horizontal distance of 32 mm from the centerline. The sample shall be considered a failure if the aluminum foil witness sheet is punctured or if the sample is cracked.
http://www.safetyglassesusa.com/milprf31013.html
och
http://www.revisioneyewear.com/technology.html
Jag hittade ingen bild på formen för en T 37 men en grej som väger ~0,4 gram med en diameter på en sådär 4mm som kommer farandes i 200m/s skall glasögonen stå emot - om jag fick till konverteringen från amerikanska mått rätt.
MVH
Hans
There are many specific categories outlined in the PRF-31013 standard. The most common clause referenced in the standard is that of 3.5.1.1 for ballistics/impact testing. In general conversation, references to an eyewear's "ballistics" rating commonly refer to its ability to withstand impact at high velocity. Thus, we will focus on this area. To see our selection of Ballistic eyewear, click here.
3.5.1.1
Ballistic Resistance
The ballistic resistance of the spectacles shall be such that they will pass a Vo test using a 0.15 caliber, 5.8 grain, T37 shaped projectile at a velocity of 640 to 660 feet per second when tested as specified in 4.4.1.1.
4.4.1.1
Ballistic Resistance
The test shall be a Vo test conducted as specified in MIL-STD-662 using a 0.15 caliber, 5.8 grain, T37 shaped projectile with the following exceptions: electronic velocity detection devices (light beam or acoustic type) may be used to determine the velocity of the projectile, such devices placed no less than 8 inches and no more than 24 inches from the target; compressed gas propulsion of the projectile may be used. The eyewear shall be mounted on an Alderson 50th percentile male headform in the as-worn position. The 0.002 inch thick aluminum foil witness sheet shall be mounted within 2 inches of the eyewear behind the area of impact. The sample shall be hit once at normal incidence within a l-inch diameter at a point centered vertically and at a horizontal distance of 32 mm from the centerline. The sample shall be considered a failure if the aluminum foil witness sheet is punctured or if the sample is cracked.
http://www.safetyglassesusa.com/milprf31013.html
och
http://www.revisioneyewear.com/technology.html
Jag hittade ingen bild på formen för en T 37 men en grej som väger ~0,4 gram med en diameter på en sådär 4mm som kommer farandes i 200m/s skall glasögonen stå emot - om jag fick till konverteringen från amerikanska mått rätt.
MVH
Hans